Model6253 Overwatch
OverWatch - Installation - Snorkel PHX-II (OLD Pre 2021 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old Snorkel PHX-II Series Installations Operator Sensor Installation Steps: 1. Drill two 5.2mm holes to mount the operator sensor in the position shown in the diagram. 2. The sensor should be ...
OverWatch - Installation - Skyjack Skycoded (OLD Pre 2021 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old Skyjack Skycoded Series Installations If any decals are damaged during the installation process or if any decals are obstructed following the installation, they should be replaced accordingly. ...
OverWatch - Installation - JLG 330LRT (OLD Pre 2021 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old LGMG-E Installations Operator Sensor Installation Steps: 1. Mount the operator sensor to the supplied bracket, using the supplied M4 washers and security bolts 2. Position the bracket in the ...
OverWatch - Installation - Sinoboom E Series (OLD Pre 2021 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old Sinoboom E Series Installations The latest version of the Sinoboom E Series kit utilises a daughter board with spring loaded contacts that connect to the LGMG control board. As we no longer ...
OverWatch - Installation - LGMG E (OLD Pre 2022 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old LGMG-E Installations The latest version of the LGMG-E kit utilises a daughter board with spring loaded contacts that connect to the LGMG control board. As we no longer publish or maintain an ...
OverWatch - Installation - LGMG RT (OLD Pre 2023 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old LGMG RT installations Operator Sensor Installation Steps: 1. Mount the operator sensor to the mounting bracket using the supplied bolts to the 30 degree position as shown 2. Drill two M6 holes ...
OverWatch - Installation - JLG MRT (OLD Pre 2021 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old JLG MRT installations Please note that the Software Version 9 and 8 updates are not compatible with the Pre 2021 harness in this old kit. You will need to update your harness in order to ...
OverWatch - Installation - JLG ERT (OLD Pre 2022 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old JLG ERT installations Operator Sensor Installation Steps: 1. Undo the bolt on the side of the control box to get access to the side plate and the bottom control box wiring 2. Mount the ...
OverWatch - Installation - Genie Smartlink (OLD Pre 2021 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old Genie Smartlink installations The latest version of the Genie Smartlink kit utilises a daughter board with spring loaded contacts that connect to the Genie control board. As we no longer ...
OverWatch - Installation - Genie Gen5 (OLD Pre 2022 Harness) - Installation Instructions
This Tech Doc was written to help customers with very old Genie Gen5 installations The latest version of the Genie Gen 5 kit utilises a daughter board with spring loaded contacts that connect to the Genie control board. As we no longer publish or ...
Overwatch - Software - V9 not compatible with Genie Gen 5 Pre-2022 Harness
The original Overwatch Harness on the Genie Gen 5 control box is incompatible with Overwatch V9 software The original solder in harness is very different to the current harness and can be identified by comparing it to the photos below. If your ...
OverWatch - Installation - Active Signal Decoder Wiring Diagram
Some JLG models have been updated to use an active signal decoder in the loom for sensing the drive and elevate functions Affected models: JLG Mxx69LE JLG xx94RT JLG xxxMRT On page 22 of the Installation Manuals for each of these listed above models ...
OverWatch - Installation - All Installation Manuals have a Harness Drawing
All Overwatch Installation Manuals have a Harness Drawing and are usually situated towards the end of each of these manuals EQSS publishes all Overwatch Installation manuals on their website via the link - Overwatch Manuals Each of the Installation ...
OverWatch - Installation - Generic Troubleshooting Diagram
Generic Overwatch to machine interface diagram Even though the diagram below is specific to the Haulotte Opti 8, it's being published here as a generic representation for most other brands and models. The Overwatch interfaces to most brands and ...
OverWatch - Installation -Genie 2-Speed Lift Conversion
If the control box has 2 speed lift then a Genie update is required Below: Photo of the affected Genie Control Box EQSS does manufacture an Overwatch kit for the following models: Scissors GS-1530 GS-1532 GS-1930 GS-1932 GS-2646 GS-4047 Masts GR-12 ...
OverWatch - Installation - Snorkel SxxxxE Harness Soldering
As part of the kit installation process, the Overwatch Snorkel SxxxxE harness requires splicing and soldering This Tech Doc was not written as a step by step installation guide, but rather further guidance whilst following the actual published pdf ...
OverWatch - Installation - Haulotte DX Pre 2010 Harness Soldering
As part of the kit installation process, the Overwatch Haulotte DX Pre 2010 harness requires splicing and soldering This Tech Doc was not written as a step by step installation guide, but rather further guidance whilst following the actual published ...
OverWatch - Installation - Haulotte HSxxE Harness Soldering
As part of the kit installation process, the Overwatch Haulotte harness requires some soldering This Tech Doc was not written as a step by step installation guide, but rather further guidance whilst following the actual published pdf installation ...
OverWatch - Installation - JLG MRT, 94RT, 69LE Harness Soldering
As part of the kit installation process, the Overwatch JLG MRT harness requires some soldering This Tech Doc was not written as a step by step installation guide, but rather further guidance whilst following the actual published pdf installation ...
OverWatch - Installation - Genie RT Harness Soldering
As part of the kit installation process, the Overwatch Genie RT harness requires some soldering This Tech Doc was not written as a step by step installation guide, but rather further guidance whilst following the actual published pdf installation ...
OverWatch - Software - Installation Test (Software V9)
Select MEWP & Run System Test Stand in front of the control box as though you are about to drive the MEWP. The sensor expects to see you at arms length. Power on the MEWP. When the OverWatch starts up, Overwatch Version 9 is announced, put the ...
OverWatch - Software - V9 Firmware Update and Installation Test
Before applying the update, understand and ensure the following: Follow all steps in this procedure, exactly as written and in the correct order. If this procedure is not followed, the update will not be successful. Do not modify or deviate from this ...
OverWatch - Software - Stabilisers failing test on Genie RT (Version 8 and lower)
There are hidden buttons under the Genie RT decal required to pass Overwatch Installation tests The Overwatch Installation test must be performed when an Overwatch kit is first installed on a Genie RT model. One of the final tests is the ...
OverWatch - User - Stabilisers on Rough Terrain Machines
All Rough Terrain machines MUST have all stabilisers fully engaged or fully disengaged - or the machines will be inhibited from functioning by the control box of your Rough Terrain machine Most brands and models of 4x4 diesel scissors (in order to ...
OverWatch Logging
Obtaining the logs The logs are available after connecting to the OverWatch Wifi and clicking on "View logs" on the Overwatch main menu (192.168.4.1). Clicking on "Download CSV" will compile the log into a CSV file and save it to your device so it ...
OverWatch - User - Quick Start Guide
This quick start guide is specific to Overwatch Version 9 software
OverWatch - User - Overwatch EWP Safety in Industry (Software V9)
This Tech Doc applies to: MEWP Operators, Site managers and supervisors, Ground staff What is EQSS Overwatch? The EQSS Overwatch is an Elevated Work Platform (EWP) operator monitoring and cutout type of crush protection system (sometimes called ...
OverWatch - Software - Installation Test for Diesel (RT) Rough Terrain
Rough Terrain machines with diesel engines must be running before attempting final Overwatch installation setup test Post Installation Configuration After the OverWatch has been installed, it must be configured with the parameters to suit the ...
OverWatch - Installation - ECU modules are NOT Waterproof
EQSS first engineers a kit and then carefully document how best that kit should be installed (step-by-step) on specific EWPs. Problems occur when the EQSS installation manual is not followed. In particular, the Overwatch ECU must be mounted inside ...
OverWatch - Installation - Sensor Mounting Guard V2 (0 Degree Lateral Angle)
This guard (AS002326) supersedes the original V1 design. Some Overwatch installs require the sensor to be angled straight on at 0 degrees lateral. This sensor angling is accomplished by screwing the inner metal sensor carrier into the 0 degree ...
OverWatch - Installation - Sensor Mounting Guard V2 (7.5 Degree Lateral Angle)
This guard (AS002326) supersedes the original V1 design. Some Overwatch installs require the sensor to be angled outwards (laterally away from the joystick) by 7.5 degrees. This sensor angling is accomplished by screwing the inner metal sensor ...
OverWatch - User - OverWatch Inspection Checklist
It is recommended to complete an inspection of the EQSS OverWatch system as part of the MEWP pre-hire inspection and the periodic 3 monthly inspection. The goal is to confirm the OverWatch is functioning correctly and is undamaged. This inspection is ...
Overwatch - Faults - Not Passing Installation Tests (OEM lights)
Some EQSS Overwatch kits receive their control signals from scissor control box LED display circuits. Overwatch kits are engineered and adapted to reliably function as a safety cutout system. Various control signals (within the scissor control box) ...
OverWatch - User - Periodic Testing
Testing must be performed on the OverWatch™ components to ensure the system operates correctly. This testing must be performed every 12 months or after any type of maintenance or repair work has been carried out on the machine’s control box. Connect ...
OverWatch - User - Inspection & Maintenance
Regular maintenance must be performed on the OverWatch™ components to ensure the system operates correctly. This maintenance must be performed every 12 months in a rental situation, or before the machine is released to the hire customer.
OverWatch - Software - Retrieving Event logs
The Log Viewer page allows viewing and downloading of the log file information. The log information is time stamped and details the event and associated parameters / measurements at the time of an event. The log data can be downloaded in a csv format ...
OverWatch - Software - Diagnostics
The diagnostics page allows real time monitoring of the sensor data. The purpose of this Tech Doc is to offer an example of what is meant when a customer is requested to retrieve Overwatch diagnostics for EQSS to analyse as part of a customer trouble ...
OverWatch - User - WiFi Access
The OverWatch includes an embedded web server, accessible via Wi-Fi. The use of this interface is limited to viewing the system’s diagnostic information, performing routine tests on all inputs/outputs and accessing the time stamped log files. Minimum ...
OverWatch - User - Drive Mode (Version 8 Software)
The OverWatch Version 8 will apply the cutout when the machine mode is Drive according to the following table: The OverWatch Version 9 will apply the cutout when the machine mode is Drive according to the following table:
OverWatch - User - Elevate Mode
The OverWatch Version 8 will apply the cutout when the machine mode is Elevate according to the following table: The OverWatch Version 9 will apply the cutout when the machine mode is Elevate according to the following table:
Next page