Model6286 Gen4
Gen4 - Installation - Haulotte HTL 4017 Light Tower Cable
This Tech Doc describes how to complete the Light Tower Cable Installation Installation Steps: 1. Feed the cable down the side of the cabin (as shown below in the image). 2. Connect the cable to the 3-pin connector labelled “Light Tower”.
Gen4 - Installation - Haulotte HTL 4017 Camera Cables
This Tech Doc describes how to complete the Camera Cables Installation Installation Steps: 1. Run the reverse camera cable towards the cabin, and secure to the existing hydraulic lines and harnesses along the chassis. 2. Connect the cable to the ...
Gen4 - Installation - Haulotte HTL 4017 Sensor Input Harness
This Tech Doc describes how to complete the Sensor Input Harness Installation Installation Steps: 1. Connect the large black bulkhead connector on the sensor input harness to the SPM. 2. Run the bps and pressure sensor cables to the rear of the ...
Gen4 - Installation - Haulotte HTL 4017 Machine Connections
The following procedures connect the safety systems to the existing electronics in the machine Installation Steps: 1. Isolate the machine before continuing to avoid damage to the electronic modules. 2. Locate the connector CN08 which can be found ...
Gen4 - Installation - Haulotte HTL 4017 Display Installation
The display shows the current safety status of the telehandler Installation Steps: 1. Position the display bracket in the top right of the dashboard (in the approximate location shown below). 2. Drill two 7 mm holes to attach the bracket to the ...
Gen4 - Installation - Haulotte HTL 4017 SPM Installation
The SPM is main processing unit and calculates the safe stability regions of the machine Installation Steps: 1. Drill four M6 holes for the SPM in the side of the cabin in the location shown. 2. Mount using the supplied M6 bolts and nuts. Below: SPM ...
Gen4 - Installation - Haulotte HTL 4017 Light Tower Installation
The light tower warns other workers when the telehandler is lifting loads close to its maximum capacity Installation Steps: 1. Drill and tap two M5 holes in the location specified to mount the light tower bracket. 2. Attach the light tower to the ...
Gen4 - Installation - Haulotte HTL 4017 Forward Camera Installation
The forward or side wheel camera is displayed when the telehandler is in forward gear. It is positioned to show the view of the front right wheel, which is usually obstructed from the view of the operator by the boom (while performing a ...
Gen4 - Installation - Haulotte HTL 4017 Reverse Camera Installation
The reverse camera video is displayed on the screen when the machine is in reverse gear to allow the operator to see behind the telehandler while reversing Installation Steps: 1. Drill two 7mm holes for the M6 mounting bolts for the reverse camera. ...
Gen4 - Installation - Haulotte HTL 4017 Compensation Pressure Sensors Installation
Compensation Pressure Sensors Installation Steps: 1. Undo the hydraulic connection for the head compensation into the manifold block at the rear of the machine. 2. Install the supplied tee piece and pressure sensor in line with the hydraulic ...
Gen4 - Installation - Haulotte HTL 4017 Pressure Manifold Components
Pressure Manifold Components
Gen4 - Installation - Haulotte HTL 4017 Remove Covers before Install
Remove the following covers before starting the installation Removal Steps: 1. Remove the rear cover and disconnect the license plate light. 2. Remove the side panel next to the cabin under the boom. 3. Inside the cabin remove the plastic cover under ...
Gen4 - Installation - Haulotte HTL 4014 Remove Covers before Install
Remove the following covers before starting the installation Removal Steps: 1. Remove the rear cover and disconnect the license plate light. 2. Remove the side panel next to the cabin under the boom. 3. Inside the cabin remove the plastic cover under ...
Gen4 - Installation - Haulotte HTL 4014 Machine & Display & Finalisation Harness Installation
This Tech Doc describes how to complete the Machine & Display Harness Installation Installation Steps: 1. Inside the cabin, run the large black bulkhead connector on the machine & display harness from inside the dashboard out through the gap between ...
Gen4 - Installation - Haulotte HTL 4014 Light Tower Cable
This Tech Doc describes how to complete the Light Tower Cable Installation Installation Steps: 1. Feed the cable down the side of the cabin (as shown in the image below). 2. Connect the cable to the 3-pin connector labelled “Light Tower”.
Gen4 - Installation - Haulotte HTL 4014 Camera Cables
This Tech Doc describes how to complete the Camera Cables Installation Installation Steps: 1. Run the reverse camera cable towards the cabin, and secure to the existing hydraulic lines and harnesses along the chassis. 2. Connect the cable to the ...
Gen4 - Installation - Haulotte HTL 4014 Sensor Input Harness
This Tech Doc describes how to complete the Sensor Input Harness Installation Installation Steps: 1. Connect the large black bulkhead connector on the sensor input harness to the SPM. 2. Run the bps and pressure sensor cables to the rear of the ...
Gen4 - Installation - Haulotte HTL 4014 Machine Connections
The following procedures connect the safety systems to the existing electronics in the machine Installation Steps: 1. Isolate the machine before continuing to avoid damage to the electronic modules. 2. Locate the connector CN08 which can be found ...
Gen4 - Installation - Haulotte HTL 4014 Display Installation
The display shows the current safety status of the telehandler Installation Steps: 1. Position the display bracket in the top right of the dashboard in the approximate location (shown below). 2. Drill two 7 mm holes to attach the bracket to the ...
Gen4 - Installation - Haulotte HTL 4014 SPM Installation
The SPM is main processing unit and calculates the safe stability regions of the machine Installation Steps: 1. Drill four M6 holes for the SPM in the side of the cabin in the location shown. 2. Mount using the supplied M6 bolts and nuts
Gen4 - Installation - Haulotte HTL 4014 Light Tower Installation
The light tower warns other workers when the telehandler is lifting loads close to its maximum capacity Installation Steps: 1. Attach the light tower to the roof of the cabin using the nuts, screws, and washers’ supplies. 2. The light tower cable ...
Gen4 - Installation - Haulotte HTL 4014 Forward Camera Installation
The forward or side wheel camera is displayed when the telehandler is in forward gear. It is positioned to show the view of the front right wheel, which is usually obstructed from the view of the operator by the boom (while performing a ...
Gen4 - Installation - Haulotte HTL 4014 Reverse Camera Installation
The reverse camera video is displayed on the screen when the machine is in reverse gear to allow the operator to see behind the telehandler while reversing Installation Steps: 1. Drill two 7mm holes for the M6 mounting bolts for the reverse camera. ...
Gen4 - Installation - Haulotte HTL 4014 Compensation Pressure Sensors Installation
Compensation Pressure Sensors Installation Steps: 1. Undo the hydraulic connection for the head compensation into the manifold block at the rear of the machine. 2. Install the supplied tee piece and pressure sensor in line with the hydraulic ...
Gen4 - Installation - Haulotte HTL 4014 Pressure Manifold Components
Pressure Manifold Components
Gen4 - Installation - Haulotte HTL 4014 Pressure Sensor Installation
The hydraulic pressure sensors are used to measure the lifting load of the telehandler Installation Steps: 1. Raise the boom to approximately 40 degrees 2. Support and secure the boom using an A Frame or similar apparatus. It must support at least 2 ...
Gen4 - Installation - Haulotte HTL 4017 Pressure Sensor Installation
The hydraulic pressure sensors are used to measure the lifting load of the telehandler Installation Steps: 1. Raise the boom to approximately 40 degrees. 2. Support and secure the boom using an A Frame or similar apparatus. It must support at least 2 ...
Gen4 - Installation - Haulotte HTL 4017 BPS Installation
The Boom Position Sensor (BPS) is used to measure the boom extension and boom angle to determine the maximum lifting capacity. Installation Steps: 1. Extend the boom out 1 meter in order to move the segment lip away from the BPS mounting section 2. ...
Gen4 - Installation - Haulotte HTL 4014 BPS Installation
The Boom Position Sensor (BPS) is used to measure the boom extension and boom angle to determine the maximum lifting capacity.Installation Steps: 1. Position the BPS toward the centre of the boom, so the wheels are in contact with the first boom ...
Gen4 - Attachments - Calibration Software Screen Descriptions
The following sections describe the items in the 'Load Calibration Window' of the EQSS Gen 4 Load Calibration Software. Step Field This shows the current step in the calibration procedure for the attachment. The record point steps will be repeated ...
Gen4 - Attachments - What is a Load Calibration?
The load calibration procedure will ask the operator to calibrate the load for the attachment. When the Gen 4 has an uploaded attachment load chart but no calibration information, then an attachment calibration must be performed. The ...
Gen4 - Calibration - Load Calibration Tips
This Tech Doc will offer a few suggestions to follow in order to perform an accurate calibration. The points listed below are recommended to follow for each of the calibration steps. Make sure to lower the stabilizers (if fitted) and try to level the ...
Gen4 - Calibration - Load Calibration Basic Outline
The load calibration procedure will ask the operator to calibrate the load for the attachment. The operator will be required to perform the calibration procedure for each different attachment. The first step in the procedure is to determine the ...
Gen4 - General - Identification Of Safety Functions
The main purpose of the Gen4-LMS is to engage a safety cutout when the machine is lifting a load which is beyond the capabilities of the machine for the current boom position. The safety cutout will activate in either one of two ways: Using a relay, ...
Gen4 - Hardware - Forward Camera
The forward or side wheel camera is displayed on the screen when the telehandler is in forward gear. It is positioned to show the view of the front right wheel, which is usually obstructed from the view of the operator by the boom while performing a ...
Gen4 - Hardware - Reverse Camera
The reverse camera video is displayed on the screen when the machine is in reverse gear. This device enables the operator to see behind the telehandler while reversing. Photo of rear camera mounted in position (on a Haulotte HTL4017) - with enlarged ...
Gen4 - Faults - Troubleshooting
The following section describes how to troubleshoot problems with the Gen4-LMS:
Gen4 - Maintenance - Clean Display and BPS Module
Follow the instructions below to maintain the Gen4-LMS components in optimal condition. Clean Gen4-LMS Display The Gen4-LMS display is rated to IP64 so there is no need to clean inside the display. Clean any accumulated dust on the surface of the ...
Gen4 - User - Menu System & Level Access Passwords
The menu system allows for configuring the Gen4-LMS. To enter the menu system, press the menu icon from the main screen. This will display the main menu as shown below: Swipe left and right to change between the different menu pages. The menu system ...
Gen4 - User - Display Settings
Press the display settings icon in the top right corner of the rating chart to show the display settings page. The display settings page allows the brightness and volume of the display to be adjusted. The display software version is also shown in the ...
Next page