Model6285 Gen3
Gen3 - Fault - Debug Gen3-LMS Screen Reset Cycle
The below instructions are only applicable if the Gen3-LMS does not load to the main screen and does not show "Shutting Down . . ." This indicates software corruption, contact EQSS for further debugging. The modules of the Gen3-LMS system are ...
Gen3 - Calibration - Perform Sensor Calibrations
Follow the instructions below to access the sensor calibration menu. Press Enter on the user control dial to enter the menu system. Press the arrow buttons to select System Menu. Press Enter to select the menu. Select Advanced Menu Enter the password ...
Gen3 - Fault - Debug Pressure Sensor Faults
When there is a failure of the pressure sensors in the Gen3-LMS system. The following error message will occur for each pressure sensor. N14 - Main Lift Cylinder Head Pressure Sensor Fault N15 - Main Lift Cylinder Rod Pressure Sensor Fault N16 - ...
Gen3 - Software - Enable and Setup Height Limiter
The height limiter function in the Gen3-LMS is only compatible with certain machines. To determine if the machine supports the height limiter function goto System Menu -> System Tests and enable the Boom Raise Cutout and Boom Extend Cutout and see if ...
Gen3 - Software - Apply update file to Gen3-LMS
The following instructions will describe copying an update file to the Gen3-LMS SD card so that an update can be applied. Remove the SD card from the Gen3 display and insert into the laptop Note: The Gen-3 Configuration Tool user manual here explains ...
Gen3 - Software - Adjustment of the Override time
Download and install Notepad++ from this link Remove the SD card from the Gen3 display and insert into a laptop Open the file data.cfg using Notepad++ In the top [General] section locate the following key MaximumOverrideTime=15 Change the "15" to the ...
Gen3 - Selections - Apply 3T Derating To All Attachments
Swapping SD cards to switch between normal and 3T limiting mode is not approved by EQSS. The only approved method to change between 3T limiting mode is to modify the configuration value either via the display, configuration software or manual edit. ...
Gen3 - Software - Zip Contents of SD Card
When debugging an issue with the Gen3-LMS with one of our support agents, they may ask for the contents of the SD card in the Gen3-LMS. Follow these instructions below to create a zip file containing the SD card contents, which can be emailed to our ...
Gen3 - Install - Override Switch for JCB Machines
Typically when installing a Gen3-LMS kit on a machine, we try to connect into the existing override switch to make it easier and less confusing for the operator. Unfortunately on the JCB machines the override is integrated into the LMI unit. JCB LMI ...
Gen3 - Software - Overload At Maximum Boom Angle
When the lift cylinder reaches the end of its stroke the hydraulic motor will try to increase the hydraulic pressure to continue to extend the lift cylinder. The Gen3 system reads this increased pressure as an increase in load causing the Gen3 to go ...
Gen3 - Fault - SD Card Read Only Issue
When using the Gen3 Configuration Tool you may get the following error messages Or when copying an update.tar file provided by EQSS support to the SD card you receive the following message The disk is write-protected. Remove the write-protection or ...
Gen3 - Attachments - Update Existing Gen3-LMS for New Attachments
Adding a new attachment to an existing telehandler with a Gen3-LMS system requires an update to the model configuration. To perform the update a laptop with an SD card reader and internet connection is required. The below needs to be performed ...
Gen3 - Attachments - Change Between Automatic & Manual Tool Selection
Changing settings via the display was added in Display Version 1129. Check the current display version in the Status Menu. If the version is older then follow the instructions here to update the display. Press Enter on the user control dial to enter ...
Gen3 - Selections - Disable / Enable Forward Camera (Latest Software)
Changing settings via the display was added in Display Version 1129. Check the current display version in the Status Menu. If the version is older then follow the instructions here to update the display. Press Enter on the user control dial to enter ...